Uniden EXS9910 Manuel du propriétaire

EXS 9910 5th 99.9.24 5:00 PM Page 1

7Use only the supplied AD-420 ACadapter. Do not use any other ACadapter.Connect the AC adapter to acontinuous power supply.Place the base unit close t

8Standard wall plate mountingThis phone can be mounted on any standard telephone wallplate.1 Snap the wall mountadapter into thenotches on the base.2

9Direct wall plate mountingIf you don't have a standard wall plate, you can mount your phonedirectly to the wall. Before doing this, consider the

10Installing the handset battery packCharge the battery pack for more than 16 hours before you startusing your phone.1 Press in on the battery coverre

11Battery use time (per charge)From fully charged• Four hours coutinuous use.• Seven days when the handset is in the standby mode.When the battery cha

12To prevent other parties from making unauthorized calls on yourphone line, a digital code was added to the EXS 9910. Yourphone’s handset and base sh

131 Press . The talk/battLED lights.2 Dial the phone number.3 To hang up, press or return thehandset to the base.Other OperationsTo Do

14Handset on the base1 Phone rings. The talk/battLEDflashes.2 Pick up the handset and beginspeaking.3 To hang up, press or returnthe handset t

15Ringer toneThe phone has four types of ringer tone.In standby mode, press and - on the keypad. Ringer volumeIn standby mode, press

16You can turn off the handset microphone so that the person youare talking with cannot hear you.1 Press during a telephone call.The talk/ba

Thank you for choosing the Uniden EXS 9910 cordless telephone. This phone is designed for reliability, long life, and outstandingperformance utilizing

17To locate the handset (while it’s off thebase), press on the base.The handset beeps for 15 seconds.page/findopenbackup batterypage/f

18Your EXS 9910 stores up to 24 numbers in the handset.1 Press while in standby mode.The talk/battLED flashes.2Dial the number you wish to st

19Memory dialing1 Press . The talk/battLEDlights.2 Press .3 Enter a two-digit number (01 - 20)to select the memory location youwish t

201 Press in the standby mode.The talk/battLED flashes.2 Press again.3 Enter the memory location number (01 - 20 or -

21To attach the beltclipInsert the beltclip into the holeson each side of the handset.Press down until it clicks.To remove the beltclipPull both sides

22Battery replacementand handlingWhen the operating timebecomes short, even after abattery is recharged, pleasereplace the battery.With normal usage,

23If your phone is not performing to your expectations, please trythese simple steps first.SymptomThe statusLED won'tcome on when thehandset is p

24SPECIFICATIONSGeneralThe EXS 9910 complies with FCC Parts 15 and 68.Frequency control: PLLModulation: Frequency shift keyingOperating temperature: 0

25A, BBattery packPreparing and charging...10Replacement and handling...22Beltclip installation...

26EXS 9910 5th 99.9.24 5:01 PM Page 29

volDIGITAL SPREAD SPECTRUMbatttalkmute rdl/pmemabc defghi mnopqrs tuv wxyzopertonem1 m2 m3 m4jkl12 345 678 90#talk flashopenbackup batterypage/findpow

EXS 9910 5th 99.9.24 5:01 PM Page 30

25 26 271. Handset antenna2. Headset jack cover3. Handset battery compartment4. Handset ring switch5. Handset speaker6. Talk/Batt LED7. Talk key8. Vol

Introduction / Features...inside front coverControls and Functions ...inside front coverGetting StartedRead this first...

3This cordless telephone must be set up before use. Follow these steps;Step 1 (page 4)Unpack and check the telephone and accessories.Step 2 (page 5 to

4Make sure you have received the following items in the package.If any of these items are missing or damaged, contact the UnidenParts Department(see b

5Do the following steps.• Choose the best location• Connect the base unit• Choose the dialing modeChoose the best locationBefore choosing a location f

6Connect the base unitIf you want to install the base unit on the wall, see page 8.Route the cord.To AC outletTo telephone outletTo TEL LINETo DC IN 9