Uniden BCT8 Spécifications Page 16
- Page / 68
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Applying Power for Vehicle Installation
You can power your scanner using the supplied DC cigarette lighter power cord or an DC
power cord.
DC power Installation
To power the scanner from a vehicle’s 12V power source (such as a cigarette-lighter
socket), you need a cigarette-lighter adapter.
To connect an DC cigarette-lighter power cable, insert its barrel plug into the
DC 12V jack on the rear of the scanner, then plug the power cable into your vehicle’s
cigarette lighter socket.
Note: If you use a cigarette-lighter power cable and your vehicle’s engine is running, you
might hear electrical noise from the engine while scanning. This is normal.
Caution: DC 12 V Jack can use a power source that supplies 12V DC at least 500 mA.
You must use a power source that supplies 12V DC and delivers at least
500 mA. Your standard 12V car battery should be sufficient. The cord connector’s
center tip must be set to positive and its plug must fit the scanner’s
DC 12V jack.
The supplied DC power cord meets these specifications. Using a power cord that
does not meet these specifications could damage the scanner or the adapter.
• Always connect the adapter or DC power cord to the scanner before you connect it to the
power source. When you finish, disconnect the adapter or DC power cord from the power
source before you disconnect it from the scanner.
• For added safety and to protect your scanner,
disconnect the cable from your vehicle battery’s
negative (-) terminal before you begin.
Follow these steps to connect the DC power cord.
1. Connect the power cord’s black wire to a chassis ground, such as a metal screw
attached to a metal part of the vehicle’s frame. Be sure that the screw is not insulated
from the frame by a plastic part.
2. Connect the power cord’s red wire (with in-line fuse) to a source
of voltage that turns on and off with the ignition switch, such as
a spare accessory terminal in your vehicle’s fuse box.
3. Insert the power cord’s barrel plug into the
DC 12V jack on
the rear of the scanner.
4. Reconnect the cable to the vehicle battery’s negative (-)
terminal.
12
A
N
T
.
E
X
T
.
S
P
.
D
C
1
2
V
R
E
M
O
T
E
- Precautions 2
- Contents 3
- Introduction 5
- Front and Rear Views 6
- Icon Display 7
- Terminology 8
- Feature Highlights 10
- Information on the Internet 11
- Optional Accessories 12
- Installing the BCT8 13
- Typical Mounting Methods 15
- DC power Installation 16
- Listening Safely 17
- Connecting the Clone Cable 17
- Scanning Overview 18
- How Squelch Works 19
- Setting the Squelch 19
- Highway Patrol Scanning 20
- Highway Patrol Scan Hold 21
- Highway Warning Alert 21
- Alert Tone Volume 21
- Muting the Alert Tone 21
- Alert Light Adjustment 22
- Skip Frequencies 22
- Priority Channels 22
- Trunked Highway Frequency 24
- Private Bank Scanning 25
- Duplicate Frequency Alert 26
- Memory Lock 26
- Scanning Private Bank 26
- Hold/Resume 27
- Channel Lockout 27
- Priority Scan 28
- Changing the Priority Channel 28
- Service Scanning 29
- Band Search 30
- Search Hold Feature 31
- Data Skip 31
- Frequency Skip 31
- Storing Search Frequencies 32
- Trunk Tracking 33
- Scan Lists 35
- Receiving Trunked Systems 37
- ID Scan Mode 37
- ID Scan Hold Feature 38
- ID Search Mode 38
- ID Monitor Mode 39
- Deleting a Stored ID 39
- ID Lockout 40
- Review ID Lockout 40
- Restoring Locked-out IDs 40
- Multi-Track 42
- Reception 43
- An EDACS 44
- Trunked system 44
- Special EDACS 45
- Features 45
- EDACS ID Range Search 45
- EDACS SCAT 45
- Motorola Reception 47
- Fleet Map Programming 48
- Selecting Preset Fleet Map 48
- Programming a User Fleet Map 48
- Programming a Hybrid System 49
- VHF/UHF Trunked Systems 49
- Toggling the Status Bit 50
- Control Channel Only Mode 50
- Remote Interface 52
- Clone Mode 53
- Null Modem Adapter 54
- Pin connections 54
- Care and Maintenance 56
- Troubleshooting 57
- Specifications 59
- Appendix 60
- Preset Fleet Maps 61
- User Defined Fleet Maps 63
- Fleet Map Size Codes 64
- Size Code Restrictions 64
- One Year Limited Warranty 67
Produits connexes et manuels pour Les radios bidirectionnelles Uniden BCT8
(36 pages)
(32 pages)
(26 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.280 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels